Materials Science and Technology
Papers 10,000
1 page of 1,000 pages (10k results)
#1Mahdi Rezaei Moghadam (UT: University of Tehran)
#2Mehdi Malekan (UT: University of Tehran)H-Index: 15
Last. Hamed Mirzadeh (UT: University of Tehran)H-Index: 40
view all 4 authors...
The effects of mischmetal addition and hot working on the enhancement of microstructure and mechanical properties of Mg–Ni alloys were studied. It was revealed that grain refinement could be achiev...
#1Mahla Shirani (Shiraz University)
#2N. Anjabin (Shiraz University)H-Index: 7
Last. Hyoung Seop Kim (POSTECH: Pohang University of Science and Technology)H-Index: 64
view all 3 authors...
The evolution of mechanical properties and microstructure of a twinning induced plasticity (TWIP) steel sheet during constrained groove pressing (CGP) was investigated. It was found that by imposin...
#1Vickey Nandal (IITD: Indian Institute of Technology Delhi)H-Index: 2
#2Krishnaswamy Hariharan (Indian Institute of Technology Madras)H-Index: 18
Last. Jayant Jain (IITD: Indian Institute of Technology Delhi)H-Index: 17
view all 9 authors...
In the present study, the influence of aging temperature on precipitation hardening in a non-equiatomic Al0.2Co1.5CrFeNi1.5Ti0.3 high-entropy alloy has been evaluated. The aging curves have been de...
Novel Cu–24Pb–xAl alloys with dispersed and rodlike Pb-rich secondary phases (PSPs) were designed and prepared with the guidance of CALPHAD. Through primary binary-phase diagram analysis and thermo...
#1K. Karthick (R.M.K. College of Engineering and Technology)
#2S. Malarvizhi (Annamalai University)H-Index: 16
Last. V. Balasubramanian (Annamalai University)H-Index: 65
view all 3 authors...
In this investigation, microstructural variation across the dissimilar weld joint between modified 9Cr-1Mo ferritic steel and 316LN stainless steel with nickel-based filler metal was fabricated and...
#1Yang Yang (CSU: Central South University)H-Index: 1
#2Hao Zhang (CSU: Central South University)H-Index: 2
Last. Min Song (CSU: Central South University)H-Index: 44
view all 5 authors...
The phase transformations and twinning in a nano-sized face-centred cubic (FCC) crystal of iron with different carbon contents are studied by molecular dynamic (MD) simulations. The simulation cell...
#1S. Chatterjee (Tata Steel)H-Index: 3
#2Manaswini Chinara (Tata Steel)H-Index: 1
Last. Subrata Mukherjee (Tata Steel)H-Index: 9
view all 6 authors...
The performance of ferrite-martensite (DP 600) and ferrite-pearlite (SPFH 590) steels with a similar tensile strength of ∼650 MPa under cyclic loading was investigated. This work presents the high ...
#1Zhi Wang (SUT: Shenyang University of Technology)H-Index: 14
#2Shouben Huang (SUT: Shenyang University of Technology)
Last. Zheng Liu (SUT: Shenyang University of Technology)H-Index: 15
view all 7 authors...
Herein, the split Hopkinson pressure bar (SHPB) technique is used to investigate the effect of aging-treatment on mechanical properties and microstructural evolution of extruded ZK60 (Mg-5.8Zn-0.72...
#1Mehrdad Kashefi (RMC: Royal Military College of Canada)
#2Thomas W. Krause (RMC: Royal Military College of Canada)H-Index: 15
Last. Shannon P. Farrell (DRDC: Defence Research and Development Canada)H-Index: 4
view all 5 authors...
Q1N samples with different degrees of tempering were produced and changes in MBN energies in non-stressed and stressed samples was investigated. It was observed that while MBN energy decreased with...
#1Jianbao Wang (Western Institute)H-Index: 6
#2Youyun Lian (Western Institute)H-Index: 11
Last. Wei Mingyu (DUT: Dalian University of Technology)H-Index: 1
view all 8 authors...
The joining of Tungsten (W) and reduced activation ferritic–martensitic steel (RAFMs) is crucial to the fabrication of divertors in future fusion reactors. In this work, an Fe75.0Si8.33B16.67 (at.-...
Top fields of study
This website uses cookies.
We use cookies to improve your online experience. By continuing to use our website we assume you agree to the placement of these cookies.
To learn more, you can find in our Privacy Policy.