Journal of Iron and Steel Research International
IF
1.26
Papers
2,534
Papers 2,772
1 page of 278 pages (2,772 results)
Newest
#1Peng Fu (JXAU: Jiangxi Agricultural University)
#2Zhi-bing Zheng (CAS: Chinese Academy of Sciences)
Last. Hao-kun Yang (Hong Kong Productivity Council)
view all 4 authors...
Mechanical properties and microstructural evolution of Fe–22Mn–0.6C and Fe–22Mn–1.0C (wt.%) twinning-induced plasticity (TWIP) steels were investigated by monotonic, stress-relaxation and unloading–reloading tensile tests. The dynamic strain aging (DSA) effect, resulting from pinning of dislocations, effectively improved the dislocation activation volume of the two TWIP steels. In the meanwhile, DSA-facilitated twinning nucleation mechanism kept similar twinning capabilities of the two TWIP stee...
Source
#1Jiantao Ju (Xi'an University of Architecture and Technology)H-Index: 1
#2Kangshuai Yang (Xi'an University of Architecture and Technology)H-Index: 2
Last. Lizhong Chang (Anhui University of Technology)H-Index: 3
view all 5 authors...
The relationship between the viscosity and structure of CaF2–CaO–Al2O3–MgO–TiO2 slag with different CaF2 contents and CaO/Al2O3 ratios was studied using the rotating cylinder method, Fourier transform infrared spectroscopy, and Raman spectrometry. The activity coefficients of CaF2 and the CaO/Al2O3 ratio were determined to understand the correlation between viscosity and structure of the slag. The results suggest that the slag viscosity reduces gradually with an increase in CaF2 content from 14....
Source
#1Lu RuH-Index: 2
#2Guangqiang LiH-Index: 28
Last. Qiang WangH-Index: 12
view all 6 authors...
Source
Source
A superior combination of yield strength (1001 MPa) and − 20 °C impact toughness (166 J) was obtained in Nb–V–Ti-microalloyed Ni–Cr–Mo–Cu steel treated by direct quenching and tempering route (DQT). The tested steels treated by DQT route and re-austenitization and tempering route (QT) were compared with each other in terms of mechanical properties and microstructures characterized by optical microscopy, transmission electron microscopy, X-ray diffraction, electron back-scattered diffraction meth...
Source
#3Yang Zeshi (NUS: National University of Singapore)H-Index: 1
#6Shuai Wang (CSU: Central South University)H-Index: 9
In the contemporary electric arc furnace (EAF) steelmaking industry, increasing contents and temperature homogenization via fluid flow stirring is found to be an effective method of improving production quality and smelting efficiency. It is a trend for different factories with bowl-shaped furnaces to apply the bath fluidity enhancement technology. EAF has plenty of advantages in modern steelmaking industry, and the improvements on the EAF steelmaking process have come up with two major tasks, n...
Source
#1Fang Yuan (USTB: University of Science and Technology Beijing)H-Index: 3
#2Zheng Zhao (USTB: University of Science and Technology Beijing)H-Index: 1
Last. Tuo Wu (USTB: University of Science and Technology Beijing)H-Index: 5
view all 4 authors...
The rheological behavior of Cr2O3-containing slags was investigated using a rotating cylinder viscometer and the solid fraction and phases of Cr2O3 in molten slags were also calculated and observed at different temperatures. Furthermore, the viscosities of CaO–SiO2–Cr2O3(–10%Al2O3) slags were measured from 1703 to 1953 K and the influence of Cr2O3 content on the viscosity and rheological behavior of molten slags was investigated. The calculation revealed that the solid fraction of the molten sla...
Source
#1Gan Min (CSU: Central South University)H-Index: 15
#2Wang Shu (CSU: Central South University)
Last. Sun Yafei (CSU: Central South University)
view all 9 authors...
Reducing the NOx emission from pelletizing process is of great importance to the green development of iron and steel industry. The flue gas temperature of preheating (PH) section during grate-kiln iron ore pelletizing process typically ranges within 850–1050 °C, which meets the temperature requirements of selective non-catalytic reduction (SNCR) for NOx. The in-bed SNCR behavior of NOx in the PH section was investigated, and the influence of relevant parameters was revealed. Results show that wi...
Source
#1Solomon-Oshioke Agbedor (Hohai University)H-Index: 1
#2Donghui Yang (Hohai University)H-Index: 21
Last. Aibin Ma (Hohai University)H-Index: 33
view all 9 authors...
Porous metals are a class of cellular materials with lightweight and unique mechanical, electrical, thermal, physical and acoustic characteristics. Magnesium and magnesium alloy foams have exhibited excellent advantages. In particular, open-cell Mg-based foams (porous Mg/Mg alloy foams) have been used for bioresorbable implants, CO2 trapping systems, filters, heat exchangers, absorbent panels and many other applications. While significant progress has been taken in producing porous Mg-based foam...
Source
#1J.L. Guo (Lanzhou University of Technology)
#2Ti Jun Chen (Lanzhou University of Technology)H-Index: 5
The effects of H2SO4 concentration and current in electrochemical corrosion on surface layer softening or plasticizing of Q235 steel bar and their effects on subsequent electrochemical cold drawing (ECD) were investigated. The results indicate that the electrochemical corrosion can soften or plasticize the surface layer of Q235 steel bar and then make the subsequent ECD be conducted more easily. The softening degree and thickness of the surface layer are continuously enhanced with increasing cor...
Source
12345678910
Top fields of study
This website uses cookies.
We use cookies to improve your online experience. By continuing to use our website we assume you agree to the placement of these cookies.
To learn more, you can find in our Privacy Policy.