Effect of interleaved composite nanofibrous mats on quasi-static and impact properties of composite plate

Published on Oct 1, 2020in Iranian Polymer Journal1.899
路 DOI :10.1007/S13726-020-00845-1
Hamidreza Zarei1
Estimated H-index: 1
,
Mohammad Nazari1
Estimated H-index: 1
,
Ali Ghaseminezhad Koushali2
Estimated H-index: 2
(Shahid Beheshti University)
Source
Abstract
The necessity to produce modern composites with an acceptable impact resistance is an essential task in automobile and aerospace industry that needs to be satisfied. This capability is addressed by noteworthy energy absorption augmentation which is the most vital characteristic of such composite materials. In this paper, nanofibers are applied as interleaves to modify the delamination strength with a minimum rise in weight and thickness of the high-modulus polypropylene/epoxy composites. Nylon 6,6 nanofibers are produced by the electrospinning method. The distribution of nanofibers across the mats is examined by SEM. Innegra fabrics have been applied in composite layers production. The proper hand lay-up manufacturing of the laminates has been assured by the assistance of a hydraulic press. The energy absorption capacity at the onset of breakdown and impact resistance of the nanomodified and non-modified laminates were determined by quasi-static three-point flexural for the former and low-velocity impact tests for the latter. The obtained results were compared. The results showed a 6.2 and 16.9% increase in the energy absorption capacity of nanomodified laminates in quasi-static three-point flexural test and low-velocity impact tests, respectively. In addition, low-velocity impact tests revealed 16 and 26% improvement in maximum load capacity.
馃摉 Papers frequently viewed together
2012
4 Authors (Abu Rasel, ..., Ajit D. Kelar)
References32
Newest
#1G枚khan Demircan (Harran University)H-Index: 2
#2Murat Kisa (Harran University)H-Index: 9
Last. Bulent Aktas (Harran University)H-Index: 9
view all 4 authors...
Surface of Al2O3 nanoparticles was modified with a silane coupling agent, and aramid fiber-reinforced epoxy nanocomposites were produced using these particles. Three different types of laminated nanocomposites were produced. These nanocomposites were obtained by adding modified nanoparticles to the epoxy resin and the aramid fiber, each separately, and to both epoxy resin and aramid fiber. All nanocomposites were produced by vacuum-assisted resin infusion method. The surface-modified Al2O3 nanop...
Source
#1Samire Sabagh (TMU: Tarbiat Modares University)H-Index: 4
#2Ahmad Reza Bahramian (TMU: Tarbiat Modares University)H-Index: 20
Last. Majid Haghir Madadi (TMU: Tarbiat Modares University)H-Index: 1
view all 3 authors...
Polyethylene glycol (PEG) is established as an organic solid鈥搇iquid phase-change material (PCM) offering a wide range of enthalpies and phase transition temperatures as a function of its molecular weight. PCMs are known for their high-energy absorbance; however, they also have two main drawbacks of leakage and enthalpy reduction during melting. In this work, polyethylene glycol as a phase-change material and graphene oxide (GO), expanded graphene (EG), and epoxy resin (EP) as shape stabilizing m...
Source
#1Guizhen KeH-Index: 1
#2Xinya JinH-Index: 1
Last. Haoxuan HuH-Index: 1
view all 3 authors...
The purpose of this study is to make use of the advantages of both polyvinylidene fluoride (PVDF) and polyacrylonitrile (PAN) to fabricate a flexible electronic device. Polyvinylidene fluoride (PVDF)/polyacrylonitrile (PAN) composite fibrous mats with different blend ratios were fabricated using electrospinning. The effects of PVDF and PAN mass ratio on fiber morphology, chemical structure, thermal stability, and piezoelectric properties of the produced composite fibers were investigated by scan...
Source
#1Sahebali Manafi (IAU: Islamic Azad University)H-Index: 14
#2Syed Rahim Kiahosseini (IAU: Islamic Azad University)H-Index: 1
The most important application of polytetrafluoroethylene (PTFE) polymer in industry is its use as a solid lubricant, due to its lack of reactivity with most industrial materials. However, the PTFE polymer has low abrasive resistance that limited its usage. In this research, 0, 2, and 5% of nanoclay were added to PTFE polymer as filler, and properties of the resultant nanocomposites were investigated. For this purpose, the nanoclay was first dissolved in a solution of water and surfactant, and t...
Source
#1Ahmad Reza Ghasemi (University of Kashan)H-Index: 18
#2Mohammad Mohammadi Fesharaki (University of Kashan)H-Index: 2
Cured shape of cross-ply [02/902]T fiber-reinforced composite laminates and the effect of multi-wall carbon nanotubes (MWCNTs) on the mechanical and thermal properties of laminates have been investigated. The nanocomposite laminate used in this study is composed of three phases: carbon fiber, polymer matrix and MWCNT. The volume fractions of 0%, 1%, 2% and 3% MWCNT were used to prepare nanocomposites. The mechanical and thermal properties of nanocomposites and fiber-reinforced nanocomposite lami...
Source
#1A. Gholizadeh (AUT: Amirkabir University of Technology)H-Index: 2
#2M. Ahmadi Najafabadi (AUT: Amirkabir University of Technology)H-Index: 4
Last. Reza Mohammadi (AUT: Amirkabir University of Technology)H-Index: 11
view all 4 authors...
Abstract Nowadays, many components are made of composite laminates assembly by bolted or riveted joints. Thus, the drilling of laminates is a usual machining operation in many industries. Due to the stress concentration around the hole, different damage modes can occur during the service. In this study, the effect of interleaving Nylon 66 nanofibers between glass/epoxy laminate on decreasing damage under the three-point bending test is considered. The results showed that applying nanofibers caus...
Source
#1Roberto PalazzettiH-Index: 17
#2Andrea Zucchelli (UNIBO: University of Bologna)H-Index: 29
Abstract In the last few decades nanofibers have been developed and introduced in a vast number of industrial and research applications. One of their most effective use is as interleaved reinforcement for composite laminate materials against delamination. Nanofibrous mats have the ideal morphology to be embedded between two plies of a laminate, and a vast and deep research has been carried out investigating their effect on the global behaviour of a composite laminate. This review is the first of...
Source
#1Mahdi Heydari-Meybodi (AUT: Amirkabir University of Technology)H-Index: 7
#2Saeed Saber-Samandari (AUT: Amirkabir University of Technology)H-Index: 34
Last. Mojtaba Sadighi (AUT: Amirkabir University of Technology)H-Index: 29
view all 3 authors...
An experimental study was performed on low-velocity impact response of nanocomposite beams reinforced with different loadings of nanoclay (0, 3, 5 or 7 wt%). Using two commercially organo-modified nanoclays (Cloisite 30B and Cloisite 15A), as well as two types of manufacturing methods (hand lay-up and vacuum assisted resin transfer molding), a set of composite/nanocomposite beam samples was prepared. To apply identical boundary conditions along the width of the beam, a cylindrical impactor was s...
Source
#1A.R. MoallemzadehH-Index: 5
#2Ali Reza SabetH-Index: 12
Last. Hossein AbediniH-Index: 10
view all 3 authors...
This study investigates morphological and mechanical behaviors of polymer composite plates reinforced with surface modified glass fiber woven roving with special interest in high velocity impact response. Four types of surface modification were applied to the glass fiber surface, namely: virgin fabric (silane coupling agent removed), silane-treated (as received fabric), corona-treated virgin fabric and silane- plus corona-treated fabric. Hand layup technique was adopted to make composite plates ...
Source
#1Mohamad Fotouhi (UNIBO: University of Bologna)H-Index: 19
#2H. Saghafi (UNIBO: University of Bologna)H-Index: 18
Last. Mehdi Ahmadi (AUT: Amirkabir University of Technology)H-Index: 19
view all 7 authors...
The use of light composites when designing fast moving parts for machine tools is emerging as a very efficient solution for improving productivity. Nevertheless, several aspects of these materials ...
Source
Cited By1
Newest
#1Mahyar Fazeli (UNNC: The University of Nottingham Ningbo China)H-Index: 6
#2Faegheh Fazeli (UI: University of Isfahan)
Last. Shokooh Moghaddam (IAU: Islamic Azad University)H-Index: 1
view all 5 authors...
The principal intention of this work is to fabricate and characterize the polyamide/chitosan nanocomposite by a novel single solvent method through the electrospinning procedure. The thermal properties and morphology of prepared nanocomposite are studied by thermogravimetric analysis (TGA) and field-emission scanning electron microscopy (FE-SEM). TGA exposed that the primary decomposition temperature is reduced with rising of chitosan content in the nanocomposites and origin disintegration tempe...
Source
This website uses cookies.
We use cookies to improve your online experience. By continuing to use our website we assume you agree to the placement of these cookies.
To learn more, you can find in our Privacy Policy.